Anker SOLIX S2000 Review Efficient Backup Power for a NAS and Home Network

The Anker SOLIX S2000 makes its strongest case as a compact backup battery for equipment that stays plugged in. In my testing, it kept a NAS and two network switches running when mains power disappeared, while adding only around 2.8 W of consumption in bypass operation. Its 2000 Wh battery also delivered excellent usable energy: between 1778 and 1969 Wh across the tested outputs and loads.

There are compromises, though. The 100 W USB-C port lacks PPS and AVS, the unit has no carrying handle, and its solar input does not turn it into an automated home storage system. Here is how the European 230 V version performed, and where it makes the most sense.

Disclosure: Anker supplied the SOLIX S2000 for this review.

Key specifications of the European model

Feature Anker SOLIX S2000
Rated battery capacity 2000 Wh
AC outlets Four Schuko sockets, 230 V
Combined AC output 1500 W continuous; 3000 W peak, as specified
USB-C 1 Up to 100 W USB Power Delivery
USB-C 2 Up to 15 W, 5 V / 3 A
USB-A Up to 12 W
Standard AC charging 1100 W setting
Ultra-fast AC charging Up to 1500 W, as specified
Solar and DC input XT60i, up to 400 W
Dimensions 208 × 282 × 323.3 mm
Weight 16.2 kg
Connectivity Wi-Fi and Anker app

The 3000 W peak rating should not be confused with continuous output. The four AC sockets share a 1500 W continuous limit.

 

A compact power station that suits the home

The S2000 looks unusually restrained for a power station. Its simple housing fits naturally beside a desk, in a utility room or near networking equipment. At roughly 19 litres based on the external dimensions, it is compact for a 2 kWh unit.

However, compact does not necessarily mean easy to carry. The 16.2 kg weight and lack of a handle make this a unit I would rather leave in one place than move around a campsite regularly. For a home, garden or caravan installation, that matters less.

The front LCD is clear and useful. It shows battery percentage, input and output power, estimated remaining runtime or charging time, and active connections. Wi-Fi adds access through the Anker app, including operating modes, charging schedules and an adjustable AC charging limit.

 

Backup power for a NAS and network equipment

For me, the most interesting feature is how little energy the S2000 needs while waiting for an outage. With mains power available, its AC sockets operate through a bypass: the connected equipment receives power from the grid rather than continuously drawing from and recharging the battery.

The measurements show an additional draw of approximately 2.8 W across all four tested load points. That translates into bypass efficiencies from 95.0 % at the lowest test setting to 99.4 % at the highest.

Nominal test load Measured output Measured mains input Bypass efficiency
50 W 53.7 W 56.5 W 95.0 %
100 W 105.0 W 107.8 W 97.4 %
200 W 200.0 W 202.8 W 98.6 %
500 W 500.0 W 502.8 W 99.4 %

The nominal settings identify the test points; the percentages are calculated from the measured input and output powers. These are bypass results, not battery charging and discharging efficiencies.

Anker SOLIX S2000 UPS bypass efficiency from 95.0 to 99.4 percent with 2.8 W of additional mains draw

Anker specifies a transfer time of 10 ms or less. I did not independently measure that interval, but the practical test was successful: my UGREEN NAS and two network switches continued working when I disconnected mains power. That demonstrates compatibility with this equipment; it does not establish uninterrupted operation for every possible load.

I also recorded around 2.5–2.8 W of idle consumption with the AC outlets enabled. The particularly useful result for a permanently connected backup setup is the low additional mains draw in bypass operation.

 

How much of the 2000 Wh battery can you use

Usable capacity depends on both the output and the load. The S2000 delivered its best AC result at 300 W, with 1941 Wh. At 100 W AC, the result fell to 1778 Wh, consistent with fixed operating losses becoming more significant during a longer discharge.

Output and load Usable energy Share of rated capacity
AC at 100 W 1778 Wh 88.9 %
AC at 300 W 1941 Wh 97.1 %
AC at 750 W 1938 Wh 96.9 %
AC at 1300 W 1840 Wh 92.0 %
USB-C at 100 W 1969 Wh 98.5 %

Anker SOLIX S2000 usable capacity from 1778 to 1969 Wh across four AC loads and a 100 W USB-C load

Across all five tests, the unweighted average is 1893.2 Wh, or 94.7 % of the rated capacity. This includes the USB-C result. Looking only at the four AC tests, the average is 1874.3 Wh, or 93.7 %. Both are strong results, but the load-specific figure is more useful for estimating runtime.

At a constant 100 W AC load, the measured 1778 Wh corresponds to approximately 17.8 hours. At 300 W, 1941 Wh works out to around 6.5 hours. Actual runtime will depend on how the connected equipment’s consumption changes.

 

AC charging takes around two hours and fifteen minutes

The standard AC charging setting is 1100 W. In the recorded charging run, mains input remained near 1115–1122 W for most of the process before dropping sharply towards the end. From the start of high-power charging to the return to standby draw, the power log shows approximately 134.7 minutes, which agrees with the roughly 2 hours 15 minutes observed in the review.

Anker SOLIX S2000 AC charging curve at the standard 1100 W setting, completing in approximately 135 minutes

The charging curve also shows the low standby consumption after the battery finishes charging.

An ultra-fast mode raises the specified charging limit to 1500 W. The charging-time result above applies to the standard setting; it is not a measurement of ultra-fast mode. You can also lower the input limit in the app, for example to 500 or 600 W.

Three full charging measurements required 2440, 2471 and 2435 Wh from the mains, giving an average of 2448.7 Wh.

Anker SOLIX S2000 full recharge energy measurements of 2440, 2471 and 2435 Wh

Charging and discharging efficiency needs a separate look

Excellent usable capacity does not automatically mean excellent round-trip efficiency. Comparing the average delivered energy of 1893.2 Wh with the average charging input of 2448.7 Wh gives 77.3 %.

This is an aggregate result across all five discharge tests, including USB-C. For AC-to-AC use, using only the four AC capacity results gives approximately 76.5 %. The individual AC load results correspond to roughly 72.6–79.3 % when divided by the same average charging input. These are estimates based on the test averages rather than separately paired charge and discharge cycles at every load.

Anker SOLIX S2000 estimated round-trip efficiency by load and output, averaging 77.3 percent including USB-C

These figures describe storing mains electricity in the battery and using it later. They do not describe bypass operation, and they do not establish efficiency when charging directly from solar panels. For a NAS backup that spends most of its time on mains power, the roughly 2.8 W bypass overhead is the more relevant everyday figure. For frequent charging and discharging, round-trip losses deserve more attention.

 

USB-C delivers 100 W but misses PPS and AVS

The main USB-C port supports the following fixed USB Power Delivery profiles: 5 V / 3 A, 9 V / 3 A, 15 V / 3 A and 20 V / 5 A. That makes it useful for compatible laptops, power banks and other USB-C devices drawing up to 100 W.

However, there is no PPS or AVS support. Smartphones that rely on PPS to reach their highest charging rates will therefore have a lower charging ceiling than they would with a suitable dedicated charger. The absence of AVS also limits its protocol flexibility; 100 W on the label does not mean every phone can use that power.

The second USB-C port is limited to 15 W at 5 V / 3 A, while USB-A provides up to 12 W. These are useful extras, but the overall USB selection is modest. There is also no car socket or other DC output. The XT60i connection is an input.

 

Solar charging without automatic home energy management

You can connect suitable solar panels directly to the XT60i input, up to a specified maximum of 400 W. The input ranges given for the unit are 11–28 V at up to 8.2 A and 28–60 V at up to 12.5 A, subject to the overall 400 W limit. Panel voltage must remain within the supported range, including open-circuit voltage under the relevant conditions.

With a 13–14 V DC supply, I observed an input current of around 8 A, or approximately 100 W. The 400 W rating therefore does not apply at every input voltage.

The bigger limitation is integration. As tested, the S2000 cannot link to a smart meter to automatically capture household PV surplus, and it does not feed stored energy into the household grid. Charging schedules are available, but they are a different function from automatic surplus control.

It works as a power station charged by directly connected panels. It is much less suitable if your goal is an integrated battery for an existing rooftop or balcony solar system.

 

Verdict

The Anker SOLIX S2000 is especially appealing as a compact backup supply for a NAS, switches and other equipment at home. Its low bypass overhead is the standout result: around 2.8 W is a small ongoing cost for keeping a substantial battery ready, and the equipment used in my outage test continued working without interruption.

Usable capacity is another strength. The AC tests delivered 1778–1941 Wh, while USB-C reached 1969 Wh. Add four Schuko sockets, 1500 W continuous AC output and a standard charging time of around 2 hours 15 minutes, and the S2000 offers a convincing set of essentials for stationary use.

Its limitations are just as clear. Frequent battery cycling exposes its less impressive round-trip efficiency. USB charging lacks PPS and AVS, there is no DC output or carrying handle, and solar functionality stops short of automated household storage.

For backup power at home, those compromises may be easy to accept. For regular camping trips, demanding smartphone charging or automatic PV surplus storage, I would look for a model designed more specifically around those needs.

For more information, visit the official Anker SOLIX S2000 product page.

Pros

  • Very low bypass overhead of approximately 2.8 W
  • Successful outage test with a NAS and two network switches
  • High measured usable capacity, including strong AC results
  • Four Schuko sockets with 1500 W combined continuous output
  • Compact dimensions for a 2000 Wh power station
  • Standard AC charging in approximately 2 hours 15 minutes
  • Clear display and app with charging limits and schedules

Cons

  • Moderate round-trip efficiency when cycling the battery
  • Main USB-C port lacks PPS and AVS; second USB-C is limited to 15 W
  • No car socket or other DC output
  • No smart-meter-based PV surplus charging or grid feed-in

 

Michael Barton
Michael Barton is a Germany-based technology enthusiast and the sole author behind Charge-Test.com. With formal training in electrical engineering and years of practical testing experience, he focuses on real-world measurements of chargers, power banks and battery systems. His articles combine structured testing methodology with a practical, hands-on approach, always independent and free from paid review agreements.

Related Posts

LiThink 12V 100Ah TM Review: Capacity Tested, Bluetooth & Self-Heating

A 100Ah battery is only useful if it delivers that capacity under load. The LiThink 12V 100Ah TM does: across five discharge tests at...

CUKTECH 10 vs Xiaomi 165W Power Bank (PB1165MI) – The Ultimate 10,000 mAh High-Power Showdown

In the 10,000 mAh category, most power banks aim for portability and moderate output power. The CUKTECH 10 and the Xiaomi 165W Power Bank...

Dynesspower 24V 100Ah LiFePO4 Battery Review: 2.7 kWh Tested

A low price is only useful if a battery actually delivers the energy printed on its label. That is the main question behind this...

NOVOO RG140 Review: 140W GaN Charger, 4 Ports & PD 3.1

NOVOO's new RG140 is a 140-watt multiport charger aimed at people who want to power several demanding devices at once — or top up...

Sandberg All-in-1 Powerbank 27000 PD 240W Review – USB PD 3.2 with AVS Support

With the All-in-1 Powerbank 27000 PD 240W, Sandberg enters the high-performance power bank segment. On paper, this model directly targets flagship devices from brands...